Front | Control Arm Lower Assembly Kit
| TRC1068 | 1 | | $295.00 |
Control/Trailing Arm, wheel suspensionControl Arm Lower Assembly KitVehicle Application Information: - does not suit ST with 14mm bolt
Left and Right Arms for Standard Replacement and Repair Upgrade This front lower control arm kit has been designed to be an easy repair solution. Offering both alignment and vehicle handling improvements. Designed not just as a repair solution but as an upgrade! Supplied as a complete kit and fully assembled with special uprated ball joints and proprietary SuperPro bushings. We have made TRC1068 by far the best choice on the market. These arms utilise the SuperPro bushings and are manufactured from a high strength material. By eliminating the O.E style rubber bushing, these arms have been optimised for longevity, durability and performance, without any unwanted NVH. SuperPro Control Arms are perfectly suited as a standard replacement and are an upgrade from the factory arms, eliminating the undesirable arm movement to maintain better steering geometry in all driving conditions.
SuperPro Tip - SuperPro strongly advises that both arms should always be replaced at the same time to maintain the correct geometry and operation of the vehicle.Vehicle Application Information: - standard replacement
- Includes Ball Joint
- Axle alignment required after fitting
- Fitting Position: Front
- Fitting Difficulty: difficult
- Fitting time [min]: 120
- Part of kit: (x)
|
Front | Control Arm Lower Assembly Kit - Offset
| TRC1069 | 1 | | $286.00 |
Control/Trailing Arm, wheel suspensionControl Arm Lower Assembly Kit - OffsetVehicle Application Information: - does not suit ST with 14mm bolt
Left and Right Arms with Offset Bushes for Standard Replacement and Repair Upgrade This front lower control arm kit has been designed to be an easy repair solution. Offering both alignment and vehicle handling improvements. Designed not just as a repair solution but as an upgrade! Supplied as a complete kit and fully assembled with special uprated ball joints and proprietary SuperPro bushings. We have made TRC1068 by far the best choice on the market. These arms utilise the SuperPro bushings and are manufactured from a high strength material. By eliminating the O.E style rubber bushing, these arms have been optimised for longevity, durability and performance, without any unwanted NVH. SuperPro Control Arms are perfectly suited as a standard replacement and are an upgrade from the factory arms, eliminating the undesirable arm movement to maintain better steering geometry in all driving conditions.
SuperPro Tip - SuperPro strongly advises that both arms should always be replaced at the same time to maintain the correct geometry and operation of the vehicle.Vehicle Application Information: - alignment correction
- Includes Ball Joint
- Fitting time [min]: 120
- Fitting Position: Front
- Fitting Difficulty: difficult
- Axle alignment required after fitting
- Part of kit: (x)
|
Front | Control Arm Lower Inner Front Bush Kit
| SPF3637K | 1 | | $71.00 |
Mounting Kit, control/trailing arm mountingControl Arm Lower Inner Front Bush KitVehicle Application Information: - does not suit ST with 14mm bolt
Vehicle Application Information: - Fitting Difficulty: difficult
- Fitting time [min]: 180
- Axle alignment required after fitting
- Fitting Position: Front
- Axle alignment required after fitting
- Fitting Difficulty: difficult
- Fitting Position: Front
- Fitting time [min]: 180
- Part of kit: (x)
|
Front | Control Arm Lower Inner Rear Bush Kit
| SPF3636K | 1 | | $194.00 |
Mounting Kit, control/trailing arm mountingControl Arm Lower Inner Rear Bush KitVehicle Application Information: - Fitting time [min]: 180
- Fitting Difficulty: difficult
- Fitting Position: Front
- Axle alignment required after fitting
- Axle alignment required after fitting
- Fitting time [min]: 180
- Fitting Difficulty: difficult
- Fitting Position: Front
- Part of kit: (x)
|
Front | Control Arm Lower Inner Rear Bush Kit - Double Offset
| SPF3641K | 1 | | $194.00 |
Mounting Kit, control/trailing arm mountingControl Arm Lower Inner Rear Bush Kit - Double OffsetA Double Offset kit is used for enhanced handling performance and will deliver positive caster to both sides of the vehicle. The vehicle will have improved directional stability, crisper, more responsive steering and improved 'return to centre' feel. This is a non tyre wearing geometry change that has a substantial effect on a vehicles handling characteristics.
Follow the installation instructions and enjoy the results! Vehicle Application Information: - Fitting Position: Front
- Fitting Difficulty: difficult
- Axle alignment required after fitting
- Fitting time [min]: 180
- Part of kit: (x)
|
Front | Control Arm Lower Inner Rear Bush Kit - Single Offset
| SPF5179K | 1 | | $194.00 |
Mounting Kit, control/trailing arm mountingControl Arm Lower Inner Rear Bush Kit - Single OffsetUse this kit to rectify a steering pull after a vehicle has been aligned to the manufacturer's specifications. Supplied with an offset bush to be fitted to the passenger side and a standard bush for the driver's side, these kits stagger the caster or setback by re-positioning the ball joint slightly forward in the chassis. This is a non tyre wearing geometry change that has a substantial effect on a vehicles ability to track straight and other handling characteristics. Follow the installation instructions and the problem is solved. Vehicle Application Information: - Steering Pull Correction Kit
- use this kit to correct a slight pull to the left
- Axle alignment required after fitting
- Fitting Difficulty: difficult
- Fitting Position: Front
- Fitting time [min]: 180
- Part of kit: (x)
|
Front | Sway Bar Link
| TRC4004 | 2 | | $45.00 |
Stabiliser Bar, suspensionSway Bar Link10mm Ball Joint Link
Minimum Length 80mm - Maximum Length 320mm Vehicle Application Information: - Fitting Position: Front
- Fitting time [min]: 30
- Fitting Difficulty: easy
- Fitting Position: Rear
- Fitting Difficulty: moderate
- Fitting Difficulty: difficult
- Part of kit: (x)
|
Front | Sway Bar Link
| TRC4022 | 2 | | $39.00 |
Stabiliser Bar, suspensionSway Bar Link10mm Ball Joint Link
180 degree opposed
Length 250mm center to center Vehicle Application Information: - Fitting time [min]: 30
- Fitting Position: Front
- Fitting Difficulty: moderate
- Fitting Position: Rear
- Fitting Difficulty: easy
- Part of kit: (x)
|
Front | Sway Bar Link Kit - Heavy Duty Adjustable
| TRC10200 | 1 | | $226.00 |
Stabiliser Bar, suspensionSway Bar Link Kit - Heavy Duty Adjustable10mm Ball Joint Adjustable Link
Minimum Length 254 mm - Maximum Length 305 mm Designed to maximise the benefit of Roll Control Adjustable Sway Bars and be used in place of that hard to find O.E link.
Features & Benefits- 6060-T5 Alloy Link
- Ball for low friction and long life
- Spanner provision for on-car adjustment
- Eliminates sway bar link flex
- Allows for neutral sway bar positioning
- Maximises all positions on adjustable Sway Bars
- Suits lowered or raised vehicles
SuperPro Tip - To get the best out of these adjustable link kits, please read the fitting instructions prior to installation. - Fitting Difficulty: moderate
- Fitting time [min]: 60
- Fitting Position: Front
- Fitting Difficulty: moderate
- Fitting Position: Front
- Fitting time [min]: 60
- Fitting Position: Rear
- Fitting Position: Rear
- Part of kit: (x)
|
Front | Sway Bar Mount Bush Kit
| SPF3638-19K | 1 | | $57.00 |
Mounting, stabiliser barSway Bar Mount Bush Kitavailable Sizes 19 & 21mm Sway Bar mount bushes are an important part of the whole sway bar system. Worn or rubber bushes in these locations lead to movement in the sway bar in unwanted directions that effect the effectiveness of the sway bar. An upgrade to SuperPro bushings can return lost sway bar performance and improve handling. Vehicle Application Information: - Fitting time [min]: 120
- Fitting Position: Front
- Fitting Difficulty: difficult
- Axle alignment required after fitting
- Fitting Difficulty: difficult
- Fitting Position: Front
- Axle alignment required after fitting
- Fitting time [min]: 120
- Fitment Difficulty
- Part of kit: (x)
|
Front | Sway Bar Mount Bush Kit
| SPF3638-21K | 1 | | $57.00 |
Mounting, stabiliser barSway Bar Mount Bush Kitavailable Sizes 19 & 21mm Sway Bar mount bushes are an important part of the whole sway bar system. Worn or rubber bushes in these locations lead to movement in the sway bar in unwanted directions that effect the effectiveness of the sway bar. An upgrade to SuperPro bushings can return lost sway bar performance and improve handling. Vehicle Application Information: - Fitting time [min]: 120
- Fitting Difficulty: difficult
- Fitting Position: Front
- Axle alignment required after fitting
- Fitting Difficulty: difficult
- Fitting Position: Front
- Fitting time [min]: 120
- Axle alignment required after fitting
- Part of kit: (x)
|
Rear | Beam Axle Pivot Bush Kit
| SPF3640K | 1 | | $225.00 |
Bush, beam axleBeam Axle Pivot Bush KitKit contains: - 12mm ID Tubes (Ford Fiesta)
- 16mm ID Tubes (Mazda 2)
to suit both mounting Bolts. - Fitting Position: Rear
- Axle alignment required after fitting
- Fitting Difficulty: difficult
- Fitting time [min]: 240
- Fitting Position: Rear
- Fitting time [min]: 240
- Fitting Difficulty: difficult
- Axle alignment required after fitting
- Part of kit: (x)
|