Front | Camber Adjusting Bolt Kit Adds +/- 1.5 Degrees camber | SPF4351-12K | 1 | | $53.00 |
Kit, camber adjustmentCamber Adjusting Bolt KitAdds +/- 1.5 Degrees camber Camber Bolt Kit 12mm Vehicle Application Information: - adds +/- 1.5 degrees camber
- Fitting time [min]: 60
- Fitting Position: Front
- Part of kit: (x)
|
Front | Control Arm Lower Assembly Kit Standard replacement | TRC1066 | 1 | | $342.00 |
Control/Trailing Arm, wheel suspensionControl Arm Lower Assembly KitStandard replacement Left and Right Arms for Standard Replacement and Repair Upgrade Our front lower control arm kit for the Hyundai Getz has been designed to be an easy repair solution. Offering both alignment and vehicle handling improvements. Designed not just as a repair solution but as an upgrade! Supplied as a complete kit and fully assembled with special uprated ball joints and proprietary SuperPro bushings. We have made TRC1066 by far the best choice on the market. These arms utilise the SuperPro bushings and are manufactured from a high strength material. By eliminating the O.E style rubber bushing, these arms have been optimised for longevity, durability and performance, without any unwanted NVH. SuperPro Control Arms are perfectly suited as a standard replacement and are an upgrade from the factory arms, eliminating the undesirable arm movement to maintain better steering geometry in all driving conditions.
SuperPro Tip - SuperPro strongly advises that both arms should always be replaced at the same time to maintain the correct geometry and operation of the vehicle.Vehicle Application Information: - standard replacement
- Includes Ball Joint
- Fitting Position: Front
- Fitting time [min]: 120
- Axle alignment required after fitting
- Fitting Difficulty: difficult
- Part of kit: (x)
|
Front | Control Arm Lower-Inner Front Bush Kit
| SPF1915K | 1 | | $60.00 |
Mounting Kit, control/trailing arm mountingControl Arm Lower-Inner Front Bush KitBush OD 30mm
Tube 19x12.3x54 - Fitting time [min]: 120
- Axle alignment required after fitting
- Fitting Difficulty: difficult
- Fitting Position: Front
- Part of kit: (x)
|
Front | Control Arm Lower-Inner Rear Bush Kit Standard replacement, replaces OEM Part Number 54584-1C300. Suits 63mm ID lower arm. | SPF3133K | 1 | | $209.00 |
Mounting Kit, control/trailing arm mountingControl Arm Lower-Inner Rear Bush KitStandard replacement, replaces OEM Part Number 54584-1C300. Suits 63mm ID lower arm. 2 x Standard bushings per kit - Fitting time [min]: 180
- Axle alignment required after fitting
- Fitting Difficulty: difficult
- Fitting Position: Front
- Part of kit: (x)
|
Front | Control Arm Lower-Inner Rear Bush Kit - Double Offset Alignment Correction. Suits 63mm ID lower arm. Replaces OEM Part Number 54584-1C300. | SPF3135K | 1 | | $208.00 |
Mounting Kit, control/trailing arm mountingControl Arm Lower-Inner Rear Bush Kit - Double OffsetAlignment Correction. Suits 63mm ID lower arm. Replaces OEM Part Number 54584-1C300. Vehicle Application Information: - 1 degree caster adjustment available
2 x offset bushings for caster adjustment A Double Offset kit is used for enhanced handling performance and will deliver positive caster to both sides of the vehicle. The vehicle will have improved directional stability, crisper, more responsive steering and improved 'return to centre' feel. This is a non tyre wearing geometry change that has a substantial effect on a vehicles handling characteristics.
Follow the installation instructions and enjoy the results! Vehicle Application Information: - Fitting time [min]: 180
- Fitting Position: Front
- Fitting Difficulty: difficult
- Axle alignment required after fitting
- Part of kit: (x)
|
Front | Control Arm Lower-Inner Rear Bush Kit - Single Offset Alignment Correction. Suits 63mm ID lower arm. Replaces OEM Part Number 54584-1C300. | SPF3134K | 1 | | $208.00 |
Mounting Kit, control/trailing arm mountingControl Arm Lower-Inner Rear Bush Kit - Single OffsetAlignment Correction. Suits 63mm ID lower arm. Replaces OEM Part Number 54584-1C300. Vehicle Application Information: - There must be at least 30mm of clearance between the droop stop and the chassis at ride height to avoid any damage to the arms.
Use this kit to rectify a steering pull after a vehicle has been aligned to the manufacturers specifications.
Supplied with an offset bush to be fitted to the passenger side and a standard bush for the drivers side, these kits stagger the caster or setback by repositioning the ball joint slightly forward in the chassis.
This is a non tyre wearing geometry change that has a substantial effect on a vehicles ability to track straight and other handling characteristics.
Follow the installation instructions and the problem is solved. Vehicle Application Information: - Steering Pull Correction Kit
- Fitting Difficulty: difficult
- Fitting Position: Front
- Fitting time [min]: 180
- Axle alignment required after fitting
- Part of kit: (x)
|
Front | Sway Bar Link
| TRC4004 | 2 | | $45.00 |
Stabiliser Bar, suspensionSway Bar Link10mm Ball Joint Link
Minimum Length 80mm - Maximum Length 320mm Vehicle Application Information: - Fitting Position: Front
- Fitting Difficulty: easy
- Fitting time [min]: 30
- Fitting Position: Rear
- Fitting Difficulty: moderate
- Fitting Difficulty: difficult
- Part of kit: (x)
|
Front | Sway Bar Link LHS - Standard Replacement | TRC4029L | 1 | | $39.00 |
Stabiliser Bar, suspensionSway Bar LinkLHS - Standard Replacement 10mm Ball Joint Link
152 degree opposed
Length 197mm center to center - Fitting time [min]: 30
- Fitting Position: Front
- Fitting Difficulty: moderate
- Part of kit: (x)
|
Front | Sway Bar Link RHS - Standard Replacement | TRC4029R | 1 | | $39.00 |
Stabiliser Bar, suspensionSway Bar LinkRHS - Standard Replacement 10mm Ball Joint Link
152 degree opposed
Length 197mm center to center - Fitting Difficulty: moderate
- Fitting Position: Front
- Fitting time [min]: 30
- Part of kit: (x)
|
Front | Sway Bar Link Kit - Heavy Duty Adjustable
| TRC10105 | 1 | | $220.00 |
Stabiliser Bar, suspensionSway Bar Link Kit - Heavy Duty Adjustable10mm Ball Joint Adjustable Link
Minimum Length 160 mm - Maximum Length 205 mm Designed to maximise the benefit of Roll Control Adjustable Sway Bars and be used in place of that hard to find O.E link.
Features & Benefits- 6060-T5 Alloy Link
- Ball for low friction and long life
- Spanner provision for on-car adjustment
- Eliminates sway bar link flex
- Allows for neutral sway bar positioning
- Maximises all positions on adjustable Sway Bars
- Suits lowered or raised vehicles
SuperPro Tip To get the best out of these adjustable link kits, please read the fitting instructions prior to installation. - Fitting Position: Rear
- Fitting Difficulty: moderate
- Fitting time [min]: 60
- Fitting Position: Front
- Fitting Position: Rear
- Fitting Difficulty: moderate
- Fitting time [min]: 60
- Part of kit: (x)
|
Front | Sway Bar Mount Bush Kit Measure bar diameter 20mm available | SPF3190-20K | 1 | | $54.00 |
Mounting, stabiliser barSway Bar Mount Bush KitMeasure bar diameter 20mm available - Fitting Difficulty: easy
- Fitting time [min]: 60
- Fitting Position: Front
- Part of kit: (x)
|
Rear | Beam Axle Pivot Bush Kit
| SPF4429K | 1 | | $227.00 |
Bush, beam axleBeam Axle Pivot Bush Kit- Fitting time [min]: 240
- Fitting Difficulty: difficult
- Fitting Position: Rear
- Part of kit: (x)
|