Front | Camber Adjusting Bolt Kit
| SPF4351-14K | 1 | | $58.00 |
Kit, camber adjustmentCamber Adjusting Bolt KitCamber Bolt Kit 14mm Vehicle Application Information: - adds +/- 1.5 degrees camber
- Fitting Position: Front
- Fitting time [min]: 60
- Part of kit: (x)
|
Front | Control Arm Lower Rear Bush Kit
| SPF3963K | 1 | | $190.00 |
Mounting Kit, control/trailing arm mountingControl Arm Lower Rear Bush KitVehicle Application Information: - Fitting Position: Front
- Fitting time [min]: 180
- Fitting Difficulty: difficult
- Axle alignment required after fitting
- Axle alignment required after fitting
- Fitting Position: Front
- Fitting Difficulty: difficult
- Fitting time [min]: 180
- Part of kit: (x)
|
Front | Control Arm Lower-Rear Bush Kit - Double Offset
| SPF3965K | 1 | | $190.00 |
Mounting Kit, control/trailing arm mountingControl Arm Lower-Rear Bush Kit - Double OffsetUse this kit to increase Caster for improved directional stability, turn in and control A Double Offset kit is used for enhanced handling performance and will deliver positive caster to both sides of the vehicle. The vehicle will have improved directional stability, crisper, more responsive steering and improved 'return to centre' feel. This is a non tyre wearing geometry change that has a substantial effect on a vehicles handling characteristics.
Follow the installation instructions and enjoy the results! Vehicle Application Information: - Fitting Position: Front
- Fitting time [min]: 180
- Axle alignment required after fitting
- Fitting Difficulty: difficult
- Part of kit: (x)
|
Front | Control Arm Lower-Rear Bush Kit - Single Offset
| SPF3964K | 1 | | $190.00 |
Mounting Kit, control/trailing arm mountingControl Arm Lower-Rear Bush Kit - Single OffsetUse this kit to correct a slight pull Use this kit to rectify a steering pull after a vehicle has been aligned to the manufacturers specifications. Supplied with an offset bush to be fitted to the passenger side and a standard bush for the drivers side, these kits stagger the caster or setback by repositioning the ball joint slightly forward in the chassis.
This is a non tyre wearing geometry change that has a substantial effect on a vehicles ability to track straight and other handling characteristics.
Follow the installation instructions and the problem is solved. Vehicle Application Information: - alignment correction
- Steering Pull Correction Kit
- Axle alignment required after fitting
- Fitting Position: Front
- Fitting Difficulty: difficult
- Fitting time [min]: 180
- Part of kit: (x)
|
Front | Sway Bar Link
| TRC4004 | 2 | | $45.00 |
Stabiliser Bar, suspensionSway Bar Link10mm Ball Joint Link
Minimum Length 80mm - Maximum Length 320mm Vehicle Application Information: - Fitting Position: Front
- Fitting time [min]: 30
- Fitting Difficulty: easy
- Fitting Position: Rear
- Fitting Difficulty: moderate
- Fitting Difficulty: difficult
- Part of kit: (x)
|
Front | Sway Bar Link
| TRC4022 | 2 | | $39.00 |
Stabiliser Bar, suspensionSway Bar Link10mm Ball Joint Link
180 degree opposed
Length 250mm center to center Vehicle Application Information: - Fitting time [min]: 30
- Fitting Position: Front
- Fitting Difficulty: moderate
- Fitting Position: Rear
- Fitting Difficulty: easy
- Part of kit: (x)
|
Rear | Beam Axle Pivot Bush Kit
| SPF3984K | 1 | | $235.00 |
Bush, beam axleBeam Axle Pivot Bush KitVehicle Application Information: - Axle alignment required after fitting
- Fitting time [min]: 240
- Fitting Difficulty: difficult
- Fitting Position: Rear
- Fitting Difficulty: difficult
- Part of kit: (x)
|