Front | Camber Adjusting Bolt Kit Adds +/- 1.5 Degrees camber | SPF4351-17K | 1 |  | $63.51 |
Kit, camber adjustmentCamber Adjusting Bolt KitAdds +/- 1.5 Degrees camber Camber Bolt Kit 17mm - Fitting Position: Front
- Part of kit: (x)
|
Front | Control Arm Lower Assembly Kit Left and Right Arms for Standard Replacement and Repair Upgrade | TRC1043 | 1 | | $275.00 |
 Control Arm/Trailing Arm, wheel suspensionControl Arm Lower Assembly KitLeft and Right Arms for Standard Replacement and Repair Upgrade Left and Right Replacement Arms for Repair or Repair Upgrade The SuperPro front lower control arm kit has been designed to be an easy repair solution. Offering both alignment and vehicle handling improvements. Designed not just as a repair solution but as an upgrade! Supplied as a complete kit and fully assembled with proprietary SuperPro bushings. We have made this kit by far the best choice on the market. These arms utilise the SuperPro bushings and are manufactured from a high strength material. By eliminating the O.E style rubber bushing, these arms have been optimised for longevity, durability and performance, without any unwanted NVH. SuperPro Control Arms are perfectly suited as a standard replacement and are an upgrade from the factory arms, eliminating the undesirable arm movement to maintain better steering geometry in all driving conditions.
SuperPro Tip - SuperPro strongly advises that both arms should always be replaced at the same time to maintain the correct geometry and operation of the vehicle.- Axle alignment required after fitting
- Fitting Difficulty: difficult
- Fitting Position: Front
- Fitting Time [min.]: 120
- Part of kit: (x)
|
Front | Control Arm Lower-Front Bush Kit Re-use original mounting pin | SPF2663K | 1 |  | $40.38 |
Mounting Kit, control/trailing arm mountingControl Arm Lower-Front Bush KitRe-use original mounting pin Vehicle Application Information: - Re-use original mounting pin
- Axle alignment required after fitting
- Fitting Difficulty: difficult
- Fitting Position: Front
- Fitting Time [min.]: 180
- Part of kit: (x)
|
Front | Control Arm Lower-Inner Rear Bush Kit - Double Offset Alignment Correction | SPF1267K | 1 |  | $111.68 |
Mounting Kit, control/trailing arm mountingControl Arm Lower-Inner Rear Bush Kit - Double OffsetAlignment Correction Vehicle Application Information: - 1 degree caster adjustment available
A Double Offset kit is used for enhanced handling performance and will deliver positive caster to both sides of the vehicle. The vehicle will have improved directional stability, crisper, more responsive steering and improved 'return to centre' feel. This is a non tyre wearing geometry change that has a substantial effect on a vehicles handling characteristics.
Follow the installation instructions and enjoy the results! Vehicle Application Information: - PS increased DS decrease alignment settings
- Performance Handling Kit
- Axle alignment required after fitting
- Fitting Difficulty: difficult
- Fitting Position: Front
- Fitting Time [min.]: 240
- Part of kit: (x)
|
Front | Control Arm Lower-Inner Rear Bush Kit - Single Offset Alignment Correction | SPF1266K | 1 |  | $111.68 |
Mounting Kit, control/trailing arm mountingControl Arm Lower-Inner Rear Bush Kit - Single OffsetAlignment Correction Vehicle Application Information: - 0.5 Degree Caster Adjustment available
Use this kit to rectify a steering pull after a vehicle has been aligned to the manufacturer’s specifications. Supplied with an offset bush to be fitted to the passenger side and a standard bush for the driver’s side, these kits stagger the caster or setback by repositioning the ball joint slightly forward in the chassis. This is a non tyre wearing geometry change that has a substantial effect on a vehicles ability to track straight and other handling characteristics. Follow the installation instructions and the problem is solved. Vehicle Application Information: - Steering Pull Correction Kit
- Axle alignment required after fitting
- Fitting Difficulty: difficult
- Fitting Position: Front
- Fitting Time [min.]: 240
- Part of kit: (x)
|
Front | Control Arm Lower-Rear Bush Kit Standard replacement | SPF1265K | 1 |  | $89.90 |
Mounting Kit, control/trailing arm mountingControl Arm Lower-Rear Bush KitStandard replacement Vehicle Application Information: - Axle alignment required after fitting
- Fitting Difficulty: difficult
- Fitting Position: Front
- Fitting Time [min.]: 240
- Part of kit: (x)
|
Front | Engine Steady Mount Bush Kit Large end has 50mm inside diameter | SPF1348K | 1 |  | $74.89 |
Engine MountingEngine Steady Mount Bush KitLarge end has 50mm inside diameter Vehicle Application Information: - Large end has 50mm inside diameter
- Fitting Difficulty: difficult
- Fitting Position: Front
- Fitting Time [min.]: 90
- Part of kit: (x)
|
Front | Engine Steady Mount Bush Kit Large end has 65mm inside diameter | SPF2706K | 1 |  | $103.08 |
Engine MountingEngine Steady Mount Bush KitLarge end has 65mm inside diameter Vehicle Application Information: - Large end has 65mm inside diameter
- Fitting Difficulty: difficult
- Fitting Position: Front
- Fitting Time [min.]: 120
- Part of kit: (x)
|
Front | Steering Rack & Pinion Mount Bush (Power Steering) Power steering | SPF1191K | 1 |  | $55.90 |
Bush, steering rackSteering Rack & Pinion Mount Bush (Power Steering)Power steering Vehicle Application Information: - Axle alignment required after fitting
- Fitting Difficulty: difficult
- Fitting Position: Front
- Fitting Time [min.]: 120
- Part of kit: (x)
|
Front | Sway Bar Link Standard Replacement | TRC4016 | 2 |  | $36.95 |
Stabiliser Bar, chassisSway Bar LinkStandard Replacement 10mm parallel Ball Joint Link
Length 63mm center to center - Fitting Difficulty: moderate
- Fitting Position: Front
- Fitting Time [min.]: 30
- Part of kit: (x)
|
Front | Sway Bar Mount Bush Kit Measure bar diameter 20 & 24mm available | SPF1132-23K | 1 |  | $37.28 |
Mounting, stabiliserSway Bar Mount Bush KitMeasure bar diameter 20 & 24mm available available Sizes 15, 16, 17, 18, 20, 23 & 24mm Sway Bar mount bushes are an important part of the whole sway bar system. Worn or rubber bushes in these locations lead to movement in the sway bar in unwanted directions that effect the effectiveness of the sway bar. An upgrade to SuperPro bushings can return lost sway bar performance and improve handling. Vehicle Application Information: - Fitting Difficulty: easy
- Fitting Position: Front
- Fitting Time [min.]: 45
- Part of kit: (x)
|
Rear | Camber Adjusting Bolt Kit Adds +/- 1.5 Degrees camber | SPF4351-15K | 1 |  | $54.84 |
Kit, camber adjustmentCamber Adjusting Bolt KitAdds +/- 1.5 Degrees camber Camber Bolt Kit 15mm - Fitting Position: Rear
- Part of kit: (x)
|
Rear | Control Arm Outer Bush Kit Fits outer of both front & rear arms | SPF1105K | 1 |  | $111.73 |
Mounting Kit, control/trailing arm mountingControl Arm Outer Bush KitFits outer of both front & rear arms Vehicle Application Information: - Fits outer of both front & rear arms
- Axle alignment required after fitting
- Fitting Difficulty: difficult
- Fitting Position: Rear
- Fitting Time [min.]: 240
- Part of kit: (x)
|
Rear | Sway Bar Link Cut To Length Link | TRC4004 | 2 |  | $42.32 |
Stabiliser Bar, chassisSway Bar LinkCut To Length Link 10mm Ball Joint Link
Minimum Length 80mm - Maximum Length 320mm - Fitting Difficulty: easy
- Fitting Position: Rear
- Fitting Time [min.]: 30
- Part of kit: (x)
|
Rear | Sway Bar Link Kit - Heavy Duty Adjustable
| TRC10105 | 1 |  | $210.91 |
Stabiliser Bar, chassisSway Bar Link Kit - Heavy Duty Adjustable10mm Ball Joint Adjustable Link
Minimum Length 160 mm - Maximum Length 205 mm Designed to maximise the benefit of Roll Control Adjustable Sway Bars and be used in place of that hard to find O.E link.
Features & Benefits- 6060-T5 Alloy Link
- Ball for low friction and long life
- Spanner provision for on-car adjustment
- Eliminates sway bar link flex
- Allows for neutral sway bar positioning
- Maximises all positions on adjustable Sway Bars
- Suits lowered or raised vehicles
SuperPro Tip To get the best out of these adjustable link kits, please read the fitting instructions prior to installation. - Fitting Difficulty: moderate
- Fitting Position: Rear
- Fitting Time [min.]: 60
- Part of kit: (x)
|
Rear | Sway Bar Mount Bush Kit Measure Sway Bar, 15, 16, 17mm available | SPF2297-15K | 1 |  | $44.84 |
Mounting, stabiliserSway Bar Mount Bush KitMeasure Sway Bar, 15, 16, 17mm available - Fitting Difficulty: easy
- Fitting Position: Rear
- Fitting Time [min.]: 60
- Part of kit: (x)
|
Rear | Sway Bar Mount Bush Kit Measure Sway Bar, 15, 16, 17mm available | SPF2297-16K | 1 |  | $44.84 |
Mounting, stabiliserSway Bar Mount Bush KitMeasure Sway Bar, 15, 16, 17mm available - Fitting Difficulty: easy
- Fitting Position: Rear
- Fitting Time [min.]: 60
- Part of kit: (x)
|
Rear | Sway Bar Mount Bush Kit Measure Bar Size 15, 16, 17mm available | SPF2297-18K | 1 |  | $44.84 |
Mounting, stabiliserSway Bar Mount Bush KitMeasure Bar Size 15, 16, 17mm available - Fitting Difficulty: easy
- Fitting Position: Rear
- Fitting Time [min.]: 60
- Part of kit: (x)
|
Rear | Trailing Arm Bush Kit
| SPF0823K | 1 |  | $131.91 |
Mounting Kit, control/trailing arm mountingTrailing Arm Bush Kit- Axle alignment required after fitting
- Fitting Difficulty: difficult
- Fitting Position: Rear
- Fitting Time [min.]: 180
- Part of kit: (x)
|