Front | Bump Stop Kit
| SPF1833BK | 1 |  | $104.00 |
Bump StopBump Stop Kit2 x Bump Stops & 2 x Boots per kit, 54mm Long x 67.5 Wide x 20-22mm Inside Diameter - Fitting Position: Front
- Fitting Difficulty: difficult
- Fitting Time [min.]: 120
- Part of kit: (x)
|
Front | Camber Adjusting Bolt Kit BA / ZA / ZB / ZC / ZD, Adds +/- 1.5 Degrees camber | SPF4351-12K | 1 |  | $39.00 |
Kit, camber adjustmentCamber Adjusting Bolt KitBA / ZA / ZB / ZC / ZD, Adds +/- 1.5 Degrees camber Camber Bolt Kit 12mm - Fitting Position: Front
- Part of kit: (x)
|
Front | Control Arm Lower-Inner Rear Bush Kit BA / ZA / ZB, Standard replacement | SPF3416K | 1 |  | $206.00 |
Control Arm-/Trailing Arm BushControl Arm Lower-Inner Rear Bush KitBA / ZA / ZB, Standard replacement - Fitting Difficulty: difficult
- Fitting Position: Front
- Axle alignment required after fitting
- Fitting Time [min.]: 210
- Part of kit: (x)
|
Front | Control Arm Lower-Inner Rear Bush Kit - Double Offset BA / ZA / ZB, Alignment Correction | SPF3418K | 1 |  | $206.00 |
Control Arm-/Trailing Arm BushControl Arm Lower-Inner Rear Bush Kit - Double OffsetBA / ZA / ZB, Alignment Correction Vehicle Application Information: - 1 Degree Caster Adjustment available
A Double Offset kit is used for enhanced handling performance and will deliver positive caster to both sides of the vehicle. The vehicle will have improved directional stability, crisper, more responsive steering and improved 'return to centre' feel. This is a non tyre wearing geometry change that has a substantial effect on a vehicles handling characteristics.
Follow the installation instructions and enjoy the results! Vehicle Application Information: - Fitting Time [min.]: 210
- Axle alignment required after fitting
- Fitting Difficulty: difficult
- Fitting Position: Front
- Part of kit: (x)
|
Front | Control Arm Lower-Inner Rear Bush Kit - Single Offset BA / ZA / ZB, Alignment Correction | SPF3417K | 1 |  | $206.00 |
Control Arm-/Trailing Arm BushControl Arm Lower-Inner Rear Bush Kit - Single OffsetBA / ZA / ZB, Alignment Correction Vehicle Application Information: - 0.5 Degree Caster Adjustment available
Use this kit to rectify a steering pull after a vehicle has been aligned to the manufacturers specifications.
Supplied with an offset bush to be fitted to the passenger side and a standard bush for the drivers side, these kits stagger the caster or setback by repositioning the ball joint slightly forward in the chassis.
This is a non tyre wearing geometry change that has a substantial effect on a vehicles ability to track straight and other handling characteristics.
Follow the installation instructions and the problem is solved. Vehicle Application Information: - Steering Pull Correction Kit
- Fitting Time [min.]: 210
- Fitting Difficulty: difficult
- Axle alignment required after fitting
- Fitting Position: Front
- Axle alignment required after fitting
- Part of kit: (x)
|
Front | Sway Bar Link Cut To Length Link | TRC4004 | 2 |  | $37.00 |
Sway Bar Stabiliser KitSway Bar LinkCut To Length Link 10mm Ball Joint Link
Minimum Length 80mm - Maximum Length 320mm - Fitting Position: Front
- Fitting Time [min.]: 30
- Fitting Difficulty: easy
- Part of kit: (x)
|
Front | Sway Bar Link Standard Replacement | TRC4022 | 2 |  | $32.30 |
Sway Bar Stabiliser KitSway Bar LinkStandard Replacement 10mm Ball Joint Link
180 degree opposed
Length 250mm center to center - Fitting Position: Front
- Fitting Difficulty: moderate
- Fitting Time [min.]: 30
- Part of kit: (x)
|
Front | Sway Bar Link LHS - Standard Replacement | TRC4028L | 1 |  | $32.30 |
Sway Bar Stabiliser KitSway Bar LinkLHS - Standard Replacement 10mm Ball Joint Link
160 degree opposed
Length 285mm center to center - Fitting Time [min.]: 30
- Fitting Position: Front
- Fitting Difficulty: moderate
- Part of kit: (x)
|
Front | Sway Bar Link RHS - Standard Replacement | TRC4028R | 1 |  | $32.30 |
Sway Bar Stabiliser KitSway Bar LinkRHS - Standard Replacement 10mm Ball Joint Link
160 degree opposed
Length 285mm center to center - Fitting Position: Front
- Fitting Difficulty: moderate
- Fitting Time [min.]: 30
- Part of kit: (x)
|
Front | Sway Bar Link Kit - Heavy Duty Adjustable
| TRC10160 | 1 |  | $189.50 |
Sway Bar Stabiliser KitSway Bar Link Kit - Heavy Duty Adjustable10mm Ball Joint Adjustable Link
Minimum Length 210 mm - Maximum Length 260 mm Designed to maximise the benefit of Roll Control Adjustable Sway Bars and be used in place of that hard to find O.E link.
Features & Benefits- 6060-T5 Alloy Link
- Ball for low friction and long life
- Spanner provision for on-car adjustment
- Eliminates sway bar link flex
- Allows for neutral sway bar positioning
- Maximises all positions on adjustable Sway Bars
- Suits lowered or raised vehicles
SuperPro Tip - To get the best out of these adjustable link kits, please read the fitting instructions prior to installation. - Fitting Position: Front
- Fitting Time [min.]: 60
- Fitting Difficulty: moderate
- Part of kit: (x)
|
Front | Sway Bar Mount Bush Kit
| SPF0895-20K | 1 |  | $24.00 |
Sway Bar Bush KitSway Bar Mount Bush Kitavailable Sizes 16, 18, 20 & 22 mm Vehicle Application Information: - Fitting Position: Front
- Fitting Difficulty: easy
- Fitting Time [min.]: 60
- Part of kit: (x)
|