Front | Camber Adjusting Bolt Kit Adds +/- 1.5 Degrees camber | SPF4351-12K | 1 | | $53.00 |
Kit, camber adjustmentCamber Adjusting Bolt KitAdds +/- 1.5 Degrees camber Camber Bolt Kit 12mm Vehicle Application Information: - adds +/- 1.5 degrees camber
- Fitting Position: Front
- Fitting time [min]: 60
- Part of kit: (x)
|
Front | Control Arm Lower Assembly Kit
| TRC1147 | 1 | | $373.00 |
Control/Trailing Arm, wheel suspensionControl Arm Lower Assembly KitVehicle Application Information: - includes left and right arms and all bushes
Left and Right Arms for Standard Replacement and Repair Upgrade The SuperPro front lower control arm kit has been designed to be an easy repair solution. Offering both alignment and vehicle handling improvements. Designed not just as a repair solution but as an upgrade! Supplied as a complete kit and fully assembled with special uprated ball joints and proprietary SuperPro bushings. We have made this kit by far the best choice on the market. These arms utilise the SuperPro bushings and are manufactured from a high strength material. By eliminating the O.E style rubber bushing, these arms have been optimised for longevity, durability and performance, without any unwanted NVH. SuperPro Control Arms are perfectly suited as a standard replacement and are an upgrade from the factory arms, eliminating the undesirable arm movement to maintain better steering geometry in all driving conditions.
SuperPro Tip - SuperPro strongly advises that both arms should always be replaced at the same time to maintain the correct geometry and operation of the vehicle.Vehicle Application Information: - standard replacement
- Includes Ball Joint
- Fitting Position: Front
- Fitting time [min]: 90
- Axle alignment required after fitting
- Fitting Difficulty: difficult
- Part of kit: (x)
|
Front | Control Arm Lower Inner Rear Bush Kit
| SPF3111K | 1 | | $177.00 |
Mounting Kit, control/trailing arm mountingControl Arm Lower Inner Rear Bush Kit2 x Standard bushings per kit Vehicle Application Information: - Bush OD 60mm
- standard replacement
- Axle alignment required after fitting
- Fitting Position: Front
- Fitting time [min]: 180
- Fitting Difficulty: difficult
- Part of kit: (x)
|
Front | Control Arm Lower Inner Rear Bush Kit - Double Offset
| SPF3113K | 1 | | $197.00 |
Mounting Kit, control/trailing arm mountingControl Arm Lower Inner Rear Bush Kit - Double OffsetVehicle Application Information: - 1 degree caster adjustment available
A Double Offset kit is used for enhanced handling performance and will deliver positive caster to both sides of the vehicle. The vehicle will have improved directional stability, crisper, more responsive steering and improved 'return to centre' feel. This is a non tyre wearing geometry change that has a substantial effect on a vehicles handling characteristics.
Follow the installation instructions and enjoy the results! Vehicle Application Information: - Bush OD 60mm
- alignment correction
- Axle alignment required after fitting
- Fitting time [min]: 180
- Fitting Position: Front
- Fitting Difficulty: difficult
- Part of kit: (x)
|
Front | Control Arm Lower Inner Rear Bush Kit - Single Offset
| SPF3112K | 1 | | $197.00 |
Mounting Kit, control/trailing arm mountingControl Arm Lower Inner Rear Bush Kit - Single OffsetUse this kit to rectify a steering pull after a vehicle has been aligned to the manufacturer's specifications. Supplied with an offset bush to be fitted to the passenger side and a standard bush for the driver's side, these kits stagger the caster or setback by repositioning the ball joint slightly forward in the chassis. This is a non tyre wearing geometry change that has a substantial effect on a vehicles ability to track straight and other handling characteristics. Follow the installation instructions and the problem is solved. Vehicle Application Information: - Bush OD 60mm
- alignment correction
- Steering Pull Correction Kit
- Axle alignment required after fitting
- Fitting Difficulty: difficult
- Fitting time [min]: 180
- Fitting Position: Front
- Part of kit: (x)
|
Front | Control Arm Lower-Inner Front Bush Kit
| SPF1715-14K | 1 | | $154.00 |
Mounting Kit, control/trailing arm mountingControl Arm Lower-Inner Front Bush KitCrush Tube 22.2 x 14.3 x 58 Vehicle Application Information: - Fitting time [min]: 180
- Fitting Difficulty: difficult
- Fitting Position: Front
- Axle alignment required after fitting
- Part of kit: (x)
|
Front | Control Arm Lower-Inner Front Bush Kit
| SPF1715K | 1 | | $89.00 |
Mounting Kit, control/trailing arm mountingControl Arm Lower-Inner Front Bush KitVehicle Application Information: - Fitting time [min]: 180
- Axle alignment required after fitting
- Fitting Position: Front
- Fitting Difficulty: difficult
- Axle alignment required after fitting
- Part of kit: (x)
|
Front | Sway Bar Link Bush Kit
| SPF2292BK | 1 | | $51.00 |
Mounting, stabiliser barSway Bar Link Bush Kit- Fitting Position: Front
- Fitting Difficulty: easy
- Fitting time [min]: 90
- Fitting Position: Rear
- Part of kit: (x)
|
Front | Sway Bar Mount Bush Kit
| SPF1451-26K | 1 | | $41.00 |
Mounting, stabiliser barSway Bar Mount Bush Kitavailable Sizes 14, 15, 16, 18, 19, 20 , 21, 22, 23, 24, 25, 26, 27, 28, 29 & 30mm Vehicle Application Information: - Fitting Difficulty: easy
- Fitting Position: Front
- Fitting time [min]: 45
- Fitting Position: Front
- Fitting time [min]: 45
- Fitting Difficulty: easy
- Fitting Position: Rear
- Part of kit: (x)
|
Rear | Lateral Arm Front Bush Kit
| SPF2114K | 2 | | $101.00 |
Mounting Kit, control/trailing arm mountingLateral Arm Front Bush KitVehicle Application Information: - bush located in outer hub assembly
- Axle alignment required after fitting
- Fitting Difficulty: difficult
- Fitting Position: Rear
- Fitting time [min]: 180
- Part of kit: (x)
|
Rear | Sway Bar Link Standard Replacement | TRC4057 | 2 | | $39.00 |
Stabiliser Bar, suspensionSway Bar LinkStandard Replacement 10mm Ball Joint Link to 10mm threaded Pin
Length 114mm - Fitting Difficulty: easy
- Fitting Position: Rear
- Fitting time [min]: 30
- Part of kit: (x)
|