| Front and Rear | Enhancement Bush Kit
| KIT182K | 1 |  | $546.00 |
Mounting, control/trailing armEnhancement Bush KitKit contains: - Front Control Arm Lower-Front Bush Kit
- Front Control Arm Lower-Inner Rear Bush Kit - Double Offset
- Rear Beam Axle Pivot Bush Kit
- Fitting time [min]: 420
- Fitting Difficulty: difficult
- Fitting Position: Front and Rear
- Part of kit: (x)
|
| Front | Control Arm Lower Complete Assembly Kit - Standard
| TRC1076 | 1 |  | $341.00 |
 Control/Trailing Arm, wheel suspensionControl Arm Lower Complete Assembly Kit - StandardLeft and Right Arms for Standard Replacement and Repair Upgrade The SuperPro front lower control arm kit has been designed to be an easy repair solution. Offering both alignment and vehicle handling improvements. Designed not just as a repair solution but as an upgrade! Supplied as a complete kit and fully assembled with special uprated ball joints and proprietary SuperPro bushings. We have made this kit by far the best choice on the market. These arms utilise the SuperPro bushings and are manufactured from a high strength material.
By eliminating the O.E style rubber bushing, these arms have been optimised for longevity, durability and performance, without any unwanted NVH.
SuperPro Control Arms are perfectly suited as a standard replacement and are an upgrade from the factory arms, eliminating the undesirable arm movement to maintain better steering geometry in all driving conditions.
SuperPro Tip - SuperPro strongly advises that both arms should always be replaced at the same time to maintain the correct geometry and operation of the vehicle.Vehicle Application Information: - standard replacement
- Includes Ball Joint
- Fitting Position: Front
- Fitting Difficulty: difficult
- Axle alignment required after fitting
- Fitting time [min]: 120
- Part of kit: (x)
|
| Front | Control Arm Lower-Front Bush Kit
| SPF4383K | 1 |  | $80.00 |
Mounting Kit, control/trailing arm mountingControl Arm Lower-Front Bush Kit- Fitting time [min]: 180
- Fitting Difficulty: difficult
- Fitting Position: Front
- Axle alignment required after fitting
- Axle alignment required after fitting
- Fitting time [min]: 60
- Fitting Difficulty: moderate
- Fitting Position: Front
- Fitting time [min]: 60
- Axle alignment required after fitting
- Part of kit: (x)
|
| Front | Control Arm Lower-Inner Rear Bush Kit
| SPF2100K | 1 | | $249.00 |
Mounting Kit, control/trailing arm mountingControl Arm Lower-Inner Rear Bush KitPlease check OD before ordering!
Some Hyundai/Kia models may require a 70mm OD Bush. Some Hyundai/Kia models may require a 70mm OD Bush, in this case please use SPF3776K Control arm bushes stabilise the movement of the arms to ensure the correct geometry is maintained in all situations. Worn or rubber bushes in these locations lead to dynamic changes in wheel alignment that effect the handling of a vehicle as well as the tyre life.
SuperPro Bushings solve this issue and are the perfect repair or repair upgrade solution. Vehicle Application Information: - 66mm OD
- standard replacement
- Axle alignment required after fitting
- Fitting time [min]: 180
- Fitting Position: Front
- Fitting Difficulty: difficult
- Axle alignment required after fitting
- Fitting time [min]: 180
- Fitting Position: Front
- Fitting Difficulty: difficult
- Axle alignment required after fitting
- Part of kit: (x)
|
| Front | Control Arm Lower-Inner Rear Bush Kit - Double Offset
| SPF2102K | 1 | | $249.00 |
 Mounting Kit, control/trailing arm mountingControl Arm Lower-Inner Rear Bush Kit - Double OffsetVehicle Application Information: - 1 degree caster adjustment available
Please check OD before ordering!
Some Hyundai/Kia models may require a 70mm OD Bush. Some Hyundai/Kia models may require a 70mm OD Bush, in this case please use SPF3809K.
A Double Offset kit is used for enhanced handling performance and will deliver positive caster to both sides of the vehicle.
The vehicle will have improved directional stability, crisper, more responsive steering and improved 'return to centre' feel.
This is a non tyre wearing geometry change that has a substantial effect on a vehicles handling characteristics.
Follow the installation instructions and enjoy the results! Vehicle Application Information: - alignment correction
- 66mm OD
- Fitting Position: Front
- Fitting Difficulty: difficult
- Axle alignment required after fitting
- Fitting time [min]: 180
- Fitting Position: Front
- Axle alignment required after fitting
- Fitting time [min]: 180
- Fitting Difficulty: difficult
- Fitting time [min]: 150
- Axle alignment required after fitting
- Part of kit: (x)
|
| Front | Control Arm Lower-Inner Rear Bush Kit - Single Offset
| SPF2101K | 1 | | $249.00 |
 Mounting Kit, control/trailing arm mountingControl Arm Lower-Inner Rear Bush Kit - Single OffsetVehicle Application Information: - There must be at least 30mm of clearance between the droop stop and the chassis at ride height to avoid any damage to the arms.
Please check OD before ordering!
Some Hyundai/Kia models may require a 70mm OD Bush. Some Hyundai/Kia models may require a 70mm OD Bush, in this case please use SPF3808K. Use this kit to rectify a steering pull after a vehicle has been aligned to the manufacturer's specifications.
Supplied with an offset bush to be fitted to the passenger side and a standard bush for the driver's side, these kits stagger the caster or setback by repositioning the ball joint slightly forward in the chassis.
This is a non tyre wearing geometry change that has a substantial effect on a vehicles ability to track straight and other handling characteristics.
Follow the installation instructions and the problem is solved.Vehicle Application Information: - Steering Pull Correction Kit
- 66mm OD
- alignment correction
- Fitting time [min]: 180
- Fitting Position: Front
- Axle alignment required after fitting
- Fitting Difficulty: difficult
- Fitting time [min]: 180
- Axle alignment required after fitting
- Fitting Position: Front
- Fitting Difficulty: difficult
- Axle alignment required after fitting
- Part of kit: (x)
|
| Front | Engine Steady Mount Bush Kit
| SPF3936K | 2 | | $45.00 |
Mounting, engineEngine Steady Mount Bush Kit- Fitting Position: Front
- Fitting time [min]: 60
- Fitting Difficulty: moderate
- Part of kit: (x)
|
| Front | Engine Steady Mount Bush Kit
| SPF3937K | 1 | | $55.00 |
Rubber Buffer, engine mounting systemEngine Steady Mount Bush Kit- Fitting Difficulty: moderate
- Fitting Position: Front
- Part of kit: (x)
|
| Front | Sway Bar Link Kit - Heavy Duty Adjustable
| TRC12200 | 1 | | $226.00 |
Stabiliser Bar, suspensionSway Bar Link Kit - Heavy Duty Adjustable12mm Ball Joint Adjustable Link
Minimum Length 254 mm - Maximum Length 305 mm Designed to maximise the benefit of Roll Control Adjustable Sway Bars and be used in place of that hard to find O.E link.
Features & Benefits- 6060-T5 Alloy Link
- Ball for low friction and long life
- Spanner provision for on-car adjustment
- Eliminates sway bar link flex
- Allows for neutral sway bar positioning
- Maximises all positions on adjustable Sway Bars
- Suits lowered or raised vehicles
SuperPro Tip - To get the best out of these adjustable link kits, please read the fitting instructions prior to installation. - Fitting Difficulty: moderate
- Fitting Position: Front
- Fitting time [min]: 60
- Fitting Difficulty: moderate
- Fitting Position: Front
- Fitting time [min]: 60
- Axle alignment required after fitting
- Fitting Difficulty: moderate
- Fitting Position: Rear
- Fitting Position: Rear
- Part of kit: (x)
|
| Front | Sway Bar To Chassis Bush Kit
| SPF2879-15K | 1 | | $58.00 |
Mounting, stabiliser barSway Bar To Chassis Bush Kitavailable Sizes 15, 20, 22, 24 & 27mm Vehicle Application Information: - Fitting Difficulty: easy
- Fitting Position: Rear
- Fitting time [min]: 60
- Fitting Position: Front
- Part of kit: (x)
|
| Front | Sway Bar To Chassis Bush Kit
| SPF2879-20K | 1 | | $58.00 |
Mounting, stabiliser barSway Bar To Chassis Bush Kitavailable Sizes 15, 20, 22, 24 & 27mm Vehicle Application Information: - Fitting time [min]: 60
- Fitting Position: Rear
- Fitting Difficulty: easy
- Fitting time [min]: 60
- Fitting Difficulty: easy
- Fitting Position: Rear
- Fitting Position: Front
- Part of kit: (x)
|
| Rear | Beam Axle Pivot Bush Kit
| SPF3934K | 1 | | $255.00 |
Bush, beam axleBeam Axle Pivot Bush Kit- Axle alignment required after fitting
- Fitting Difficulty: difficult
- Fitting Position: Rear
- Fitting time [min]: 240
- Part of kit: (x)
|
